INFO ESPHome 2024.12.4
INFO Reading configuration /config/printerpico.yaml...
INFO Starting log output from 10.0.1.61 using esphome API
INFO Successfully connected to printerpico @ 10.0.1.61 in 0.008s
INFO Successful handshake with printerpico @ 10.0.1.61 in 0.228s
[11:38:37][I][app:100]: ESPHome version 2024.12.4 compiled on Jan 18 2025, 08:15:47
[11:38:37][C][wifi:600]: WiFi:
[11:38:37][C][wifi:428]:   Local MAC: 28:CD:C1:0F:73:73
[11:38:37][C][wifi:433]:   SSID: 'TechnoShed'[redacted]
[11:38:37][C][wifi:436]:   IP Address: 10.0.1.61
[11:38:37][C][wifi:439]:   BSSID: B8:D4:BC:20:65:53[redacted]
[11:38:37][C][wifi:441]:   Hostname: 'printerpico'
[11:38:37][C][wifi:443]:   Signal strength: -46 dB ▂▄▆█
[11:38:37][C][wifi:447]:   Channel: 1
[11:38:37][C][wifi:448]:   Subnet: 255.255.255.0
[11:38:37][C][wifi:449]:   Gateway: 10.0.1.1
[11:38:37][C][wifi:450]:   DNS1: 10.0.1.1
[11:38:37][C][wifi:451]:   DNS2: 0.0.0.0
[11:38:37][C][logger:185]: Logger:
[11:38:37][C][logger:186]:   Level: DEBUG
[11:38:37][C][logger:188]:   Log Baud Rate: 115200
[11:38:37][C][logger:189]:   Hardware UART: USB_CDC
[11:38:37][C][gpio.output:010]: GPIO Binary Output:
[11:38:37][C][gpio.output:011]:   Pin: GPIO32
[11:38:37][C][rp2040_pio_led_strip:202]: RP2040 PIO LED Strip Light Output:
[11:38:37][C][rp2040_pio_led_strip:203]:   Pin: GPIO17
[11:38:37][C][rp2040_pio_led_strip:204]:   Number of LEDs: 32
[11:38:37][C][rp2040_pio_led_strip:205]:   RGBW: NO
[11:38:37][C][rp2040_pio_led_strip:206]:   RGB Order: GRB
[11:38:37][C][rp2040_pio_led_strip:207]:   Max Refresh Rate: 0.000000 Hz
[11:38:37][C][light:092]: Light '3D Printer Pico LED'
[11:38:37][C][light:092]: Light '3D Printer LED Strip'
[11:38:37][C][light:094]:   Default Transition Length: 1.0s
[11:38:37][C][light:095]:   Gamma Correct: 2.80
[11:38:37][C][adc.rp2040:026]: ADC Sensor 'Printer PICO Core Temperature'
[11:38:37][C][adc.rp2040:026]:   Device Class: 'voltage'
[11:38:37][C][adc.rp2040:026]:   State Class: 'measurement'
[11:38:37][C][adc.rp2040:026]:   Unit of Measurement: '°C'
[11:38:37][C][adc.rp2040:026]:   Accuracy Decimals: 2
[11:38:37][C][adc.rp2040:028]:   Pin: Temperature
[11:38:37][C][adc.rp2040:036]:   Samples: 1
[11:38:37][C][adc.rp2040:037]:   Update Interval: 60.0s
[11:38:37][C][mdns:116]: mDNS:
[11:38:37][C][mdns:117]:   Hostname: printerpico
[11:38:37][C][esphome.ota:073]: Over-The-Air updates:
[11:38:37][C][esphome.ota:074]:   Address: printerpico.local:2040
[11:38:37][C][esphome.ota:075]:   Version: 2
[11:38:37][C][esphome.ota:078]:   Password configured
[11:38:37][C][safe_mode:018]: Safe Mode:
[11:38:37][C][safe_mode:019]:   Boot considered successful after 60 seconds
[11:38:37][C][safe_mode:021]:   Invoke after 10 boot attempts
[11:38:37][C][safe_mode:022]:   Remain in safe mode for 300 seconds
[11:38:37][C][api:140]: API Server:
[11:38:37][C][api:141]:   Address: printerpico.local:6053
[11:38:37][C][api:143]:   Using noise encryption: YES